16CH H.264 HDMI&BNC Video hdmi encoder iptv

Product Detail

Brief Introduction

 

This HDMI +BNC video encoder will take lower bandwidth to get high definition video signal, it adopts H.264 encoding format, and can encode video & audio at the same time .

Its output TS dual stream design can make it to set the resolution of code steam of every channel according to different requirement .Its high integration and cost-effective design make this device widely used in IPTV systems . Beside, the system is more stable also it supports VLC decode.

 

Product Feature

 

• HDMI+BNC (CVBS) dual interface input at real time

• Support ONVIF protocol and NVR recording

• It adopts standard H.264 coding format

• Audio coding support MPEG1 Audio Layer2

• CBR/VBR/ABR code rate controlling , 16kbit/s~16Mbit/s

• Support Network interface full-duplex mode 1000M

• Support HTTP,UDP,RTSP,RTMP protocol and support unicast &

•     multicast

• The video stream output format : TS/VES/AES ect.

• Clean WEB dashboard, Chinese and English are optional.

• Support the double streaming output, main streaming + second streaming

• Be able to select different streaming resolution.

• Support decoding for multi-brand set up box

• Support transmit in WAN and LAN .

• Support HDCP .

 

Application

 

• As HD encoder for IPTV

• Digital HD/SD streaming sever.

• Video conference

• Replace HD Video Capture Card

• Hotel cable TV system

• live and recording broadcast for operating room.

• live and recording broadcast for education

• Digital HD live and recording broadcast for courtroom.

• Access to network monitoring platform, support recording broadcast

 

Specifications

 

Model number			MV-E2002BNC-16CH
Encoder	16 inputs	interface type	HDMI*1, CVBS*1
		max resolution	1920*1080@60HZ
	16 outputs	interface type	RJ45*1
		signal standard	standard network stream
		protocol type	HTTP,ONVIF,RTSP,RTMP ,multicast UDP
Size	L * W * H		48.1cm * 30cm * 13.3cm
N/W			8kg
Power			AC 220V±10%,50/60Hz
Work temperature			0?-50?
Storage temperature			-20? -85?

System


?. System settings

When in WEB control interface, the computer’s IP needed be modified as IP 192.168.1.*. the encoder’s default IP is 192.168.1.168.

Reset&Initial: there is a RST on the panel, which can be used for HD video encoder being reseted and initialized. Under condition of power on, keep pressing the RST for 10 seconds ,it will restart, which can make parameters be initialized. Then the IP will be initialized as 192.168.1.168.

1. Set the IP address as 192.168.1.*   note:* can be any number among 0-254 except 168

2. Open up IE, input 192.168.1.168 to WEB interface , username: admin  password: admin



3. HDMI status



Note:

3.1 access address: can be directly copied into VCL player to decode.

3.2 Video parameter: video signal parameter input

3.3 Audio parameter: audio signal parameter input

3.4 Hardware status: when the interrupt number rises, it means there is video inputting, when the number is “0”, it means there is no video inputting. Then the input signal need be checked.

4. Network settings



Note: the encoder’s default IP is 192.168.1.168. if you forget the IP address after you modify it, you can keep pressing the RST for 10 seconds ,it will restart, which can make parameters be initialized.

5.HDMI coding settings

5.1 : video and audio parameter settings



Note: the parameters can be adjusted according to practical application



5.2 : Network transmission protocol Settings



Note: on condition of HTTP protocol, the player can be played without HDMI.

6.the second stream settings:



Note: the configuration parameters is same as the main stream

7.RTMP protocol settings





7.1 Set H.264 level : baseline profile

7.2 Set RTMP protocol : Enable

7.3 Set RTMP sever IP

7.4 Set RTMP sever port

7.5 Set RTMP stream name

7.6 Sever test:

7.6.1  Instal software: Flash+Media+Sever3.5 there’s no need for serial number when install, both username and code are “1”.

7.6.2  start background software:



7.6.3Open up the file of FlashPlayer : VideoPlayer.html

7.6.4Type in : rtmp://ip address /rtmp/hdmi ,choose live, then can see the image or type in:rtmp://192.168.1.100:1935/live/hdmi  choose:LIVE  click:Play stream

 

8.System settings



9. Chinese & English switch



10. HDMI OSD settings



Note: if no need for watermarks, space should be entered in “text”.

? VLC decoding configuration 

1.VLC playing settings 

VLC software version NO: 2.0.1



Note:under HDMI protocol condition,the suffix added is not necessary.

2.VLC videorecording settings

Click: play











Similar Product:

  

  




If you wanna press a sample plz click this button: